How Are Single Vision Stock Lenses Manufactured?

Single vision stock lenses (also called finished single vision or FSV lenses) are mass-produced in standard, pre-calculated prescription powers—typically ranging from -8.00 to +6.00 diopters in 0.25-diopter increments. Unlike custom "surfaced" lenses, which are ground and polished on demand from semi-finished blanks, stock lenses emerge from precision molds with their final front and back optical curves already formed.

1.Mold Selection and Gasket Assembly:

Determines final sphere and cylinder power.

Technicians select two precision-ground glass molds: a concave front mold and a convex back mold. The exact curvature difference between these two glass surfaces dictates the lens's refractive power. A flexible thermoplastic gasket (typically PVC or EVA) is fitted around the perimeter of the two molds, sealing them together and leaving a precise internal cavity that defines the center and edge thickness.

2.Monomer Formulation and Filling:

Liquid optical monomer (such as CR-39 allyl diglycol carbonate, or higher-index thiourethane resins) is mixed with a chemical initiator (catalyst), UV absorbers, and sometimes blue-light-filtering dyes. The mixture is vacuum-degassed to remove microscopic air bubbles, filtered, and injected into the mold cavity through a small port in the gasket. 

3.Thermal or UV Curing (Polymerization):

12 to 24 hours for standard thermal cycles.

The filled mold assemblies are loaded onto racks and placed into programmable curing ovens—or UV curing chambers for specialized resins. Heat triggers polymerization, gradually turning the liquid monomer into a solid, cross-linked thermoset plastic. Temperature ramps must be tightly controlled because the material shrinks slightly as it hardens; uneven heating introduces internal optical stress or surface warping.

4.De-molding and Annealing:

Once cured, the plastic gasket is stripped away, and mechanical wedges or thermal shock separate the glass molds from the hardened plastic lens. The raw lenses then undergo annealing—a secondary controlled heating and cooling cycle—to relieve internal mechanical stress created during polymerization. The glass molds are cleaned, inspected, and returned to the line for reuse.

5.Hard Coating (Scratch Resistance):

Raw optical plastics are relatively soft. Lenses are ultrasonically cleaned, chemically etched for adhesion, and submerged into a liquid polysiloxane or acrylic lacquer bath (dip-coating). As the lenses are withdrawn at a strictly controlled speed, a uniform, micron-thin layer forms on both surfaces, which is then thermally cured into a hard, scratch-resistant shell.

single-vision-lenses

6.Anti-Reflective (AR) and Hydrophobic Vacuum Coating:

Cleaned lenses are loaded into high-vacuum evaporation chambers. Electron beams vaporize ultra-pure metal oxides (such as silicon dioxide and titanium or zirconium dioxide), depositing alternating sub-micron layers onto the lens surface to cancel out surface reflections via destructive interference. A final fluoropolymer topcoat is vapor-deposited to make the surface oleophobic (oil-repelling) and hydrophobic (water-repelling) for easy cleaning.

7.Automated Optical Inspection and Packaging:

High-speed automated lensometers and vision systems verify sphere, cylinder, axis, prism, center thickness, and cosmetic clarity (checking for pits, coating defects, or inclusions). Passing lenses receive temporary ink markings indicating optical center and axis orientation, are sealed in labeled protective envelopes by power, and ship to optical labs—where they only require edging (cutting the round blank to fit a specific eyeglass frame).

Key Differences by Lens Material

While the mold-casting workflow above covers thermoset plastics (CR-39 and high-index 1.60, 1.67, and 1.74), polycarbonate and Trivex stock lenses rely on slightly different forming methods:

Material Forming Method Cycle Time Key Advantage
CR-39 (1.50) Thermal mold casting 12–24 hours High optical clarity (Abbe value ~58), low cost
High-Index (1.60–1.74) Thermal mold casting 16–24 hours Thinner, flatter profile for strong prescriptions
Polycarbonate (1.59) Injection molding ~60–90 seconds Extreme impact resistance; thermoplastic pellets are melted and injected under high pressure into heated metal molds
Trivex (1.53) Cast molding 12–18 hours Combines polycarbonate-level impact resistance with near-CR-39 optical clarity

 


Post time: Nov-16-2026